From e2f250341fa03ccbeba4d0ab9fff645e90eddb2c Mon Sep 17 00:00:00 2001 From: Salt Date: Sat, 21 Jul 2018 15:11:35 -0500 Subject: [PATCH] Cava: Remove config I don't use it anymore --- .config/cava/config | 128 -------------------------------------------- 1 file changed, 128 deletions(-) delete mode 100644 .config/cava/config diff --git a/.config/cava/config b/.config/cava/config deleted file mode 100644 index ebbbd9b3..00000000 --- a/.config/cava/config +++ /dev/null @@ -1,128 +0,0 @@ -## Configuration file for CAVA. Default values are commented out. Use either ';' or '#' for commenting. - - -[general] - -# Smoothing mode. Can be 'normal', 'scientific' or 'waves'. -; mode = normal - -# Accepts only non-negative values. -; framerate = 60 - -# 'autosens' will attempt to decrease sensitivity if the bars peak. 1 = on, 0 = off -# 'overshoot' allows bars to overshoot (in % of terminal height) without initiating autosens. -autosens = 0 -; overshoot = 20 - -# Manual sensitivity in %. Autosens must be turned off for this to take effect. -# 200 means double height. Accepts only non-negative values. -sensitivity = 3 - -# The number of bars (0-200). 0 sets it to auto (fill up console). -# Bars' width and space between bars in number of characters. -; bars = 0 -bar_width = 3 -bar_spacing = 1 - - -# Lower and higher cutoff frequencies for lowest and highest bars -# the bandwidth of the visualizer. -# Note: there is a minimum total bandwidth of 43Mhz x number of bars. -# Cava will automatically increase the higher cutoff if a too low band is specified. -; lower_cutoff_freq = 50 -; higher_cutoff_freq = 10000 - - - -[input] - -# Audio capturing method. Possible methods are: 'pulse', 'alsa' or 'fifo'. -# Defaults to 'pulse', 'alsa' or 'fifo', in that order, dependent on what support cava was built with. -# -# All input methods uses the same config variable 'source' -# to define where it should get the audio. -# -# For pulseaudio 'source' will be the source. Default: 'auto', which uses the monitor source of the default sink -# (all pulseaudio sinks(outputs) have 'monitor' sources(inputs) associated with them). -# -# For alsa 'source' will be the capture device. -# For fifo 'source' will be the path to fifo-file. -method = pulse -; source = auto - -; method = alsa -; source = hw:Loopback,1 - -; method = fifo -; source = /tmp/mpd.fifo - - - -[output] - -# Ouput method. Can be 'ncurses', 'noncurses' or 'raw'. -# 'noncurses' is for systems that does not suport ncurses. -# 'raw' is a 16 bit data stream of the bar heights that can be used to send to other applications. -# 'raw' defaults to 200 bars, which can be adjusted in the 'bars' option above. -; method = ncurses - -# Visual styles. Can be 'stereo' or 'mono'. -# 'stereo' mirrors both channels with low frequencies in center. -# 'mono' averages both channels and outputs left to right lowest to highest frequencies. -; style = stereo - -# Raw output target. A fifo will be created if target does not exist. -; raw_target = /dev/stdout - -# Raw data format. Can be 'binary' or 'ascii'. -; data_format = binary - -# Binary bit format, can be '8bit' (0-255) or '16bit' (0-65530). -; bit_format = 16bit - -# Ascii max value. In 'ascii' mode range will run from 0 to value specified here -; ascii_max_range = 1000 - -# Ascii delimiters. In ascii format each bar and frame is separated by a delimiters. -# Use decimal value in ascii table (i.e. 59 = ';' and 10 = '\n' (line feed)). -; bar_delimiter = 59 -; frame_delimiter = 10 - - - -[color] - -# Colors can be one of seven predefined: black, blue, cyan, green, magenta, red, white, yellow. -# Or defined by hex code '#xxxxxx' (hex code must be within ''). -#background = '#1d2021' #bg0_h -foreground = 'cyan' - - -[smoothing] - -# Multiplier for the integral smoothing calculations. Takes values from 0-0.99. -# Higher values means smoother, but less precise. Set to 0 to disable. -; integral = 0.0 - -# Disables or enables the so-called "Monstercat smoothing". Set to 0 to disable. -; monstercat = 0 - -# Set gravity multiplier for "drop off". Higher values means bars will drop faster. -# Accepts only non-negative values. 0.5 means half gravity, 2 means double. Set to 0 to disable "drop off". -; gravity = 1 - - -# In bar height, bars that would have been lower that this will not be drawn. -; ignore = 0 - - -[eq] - -# This one is tricky. You can have as much keys as you want. -# Remember to uncomment more then one key! More keys = more precision. -# Look at readme.md on github for further explanations and examples. -1 = 1 # bass -2 = 1 -3 = 1 # midtone -4 = 1 -5 = 1 # treble